Plastic Crusher When The Power Of Work

Plastic Crusher When The Power Of Work

Date:Oct 09, 2017


Due to broken the working state of the Plastic Crusher is the need for a strong force to carry out, then the whole machine is the need to bear the strength, it is easy to lead to fixed Plastic Crusher screw cap loosening, that is, cement mill Energy-saving ball mill machine will be with the strength of the studio vibration when you need to tighten the screws in the fixed machine, of course, the impact of Plastic Crusher this work is mainly by the usual check the machine to achieve this process to repeat , Until the material is broken to the required size, the lower part of the machine until the discharge, adjust the gap between the counter and the rotor frame can be achieved to change the material size and material shape purposes.
Each machine's parts have their life, when the Plastic Crusher spindle time spent over the metallurgical rotary kiln, it will be due to wear and other reasons lead to bending deformation, resulting in a strong vibration of the machine, of course, the absolute balance Is not there, there is an error value, in general, the error value of not more than five grams, it will not be affected, if more than five grams, it must be noted, then have to replace one of the two A hammer weight equal to this time we must promptly replace the Plastic Crusher spindle, so that all aspects of the force to be able to prevent the machine after the vibration to improve its third-generation sand making machine to adjust the device, reducing downtime and maintenance time , The unique plate hammer fixture, making the plate hammer higher reliability, so that it is rough in the broken operation, simplify the process, saving time and cost, especially the PFW series of European version of the fight against Plastic Crusher, the use of World-class manufacturing process, the selection of the most high-end production materials, heavy third-generation sand molding machine design, as well as strict testing means, the rotor into Line cone Plastic Crusher analysis to ensure stable and reliable, to ensure high-quality rotor.
This machine is the use of impact energy to break the material of the plastic crushing machine, when the material into the plate hammer area, the hammer by the high-speed impact and broken, and was thrown into the rotor above the counterattack device again broken, and then From the fight against the liner back to the plate hammer area to re-broken, Plastic Crusher in the two groups of hammer is to balance the weight before they can play the maximum efficiency, it will not happen shock energy ball mill maneuver.
In the new Plastic Crusher put into operation, the work must be completed after the break every break to conduct a comprehensive inspection. After a week of operation on the anti-broken motor, lubrication to conduct a comprehensive inspection. Check the contents of the fixed parts, including fastening, belt drive, bearing seal, counter-liner, liner wear and tear of the full place of the inspection, combined with the inspection cycle to establish a regular maintenance and replacement system.
When the rotor of the mechanical Plastic Crusher is in operation, the gap between the rotor and the counter-liner can not be adjusted. Such as the material into the block in the counterattack plate and plate between the shell, it is recommended to re-adjust the gap between the slightly raised counterattack, Plastic Crusher so that the block into the feed will become loose, easy to adjust the light frame can be easily adjusted. If the degree of counterattack is not sufficient, you can tap on a loose lever (protected with a piece of wood). The gap between the rotor and the counter-liner is done by the machine's trimming device. First release the bolt and then roll the long nut. When the lever will move upward, adjust the tightening of the screw sleeve.
Mechanical Plastic Crusher replacement parts, the first open after the shelves. When used, first after the shelves and the box in the coupling bolt unloaded, and then wrench to the clamshell device hexagonal head sector, and then shelves hanging open. At the same time, you can use the suspension above the rack hanging to the rear frame; Plastic Crusher repeat the process, you can close the shelves. Counter-breaking hammer wear to a certain extent should be timely adjustment or replacement, in order to avoid damage to fasteners and other parts.

Previous: Cooling Tower Manufacturers In The Future Development

Next: Autumn And Winter Should Pay Attention To The Maintenance Of Scroll Chiller